They are making a few great points about A Step-by-Step Guide to Installing a Bathtub overall in the content just below.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Setting up a bathtub isn't exactly rocket science, but it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old tub with a new one is also a moderately hard project. If the old tub is conveniently accessible, the job can move easily; if you need to open a wall to eliminate the old bathtub and place the brand-new bathtub, the job is a lot harder. In either situation, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old tub and embeded in the brand-new one. Ensure you have certified on your own for the work and fit attempting it. As opposed to working with a contractor to take control of a halfway-completed project, it is far better to consider employing one before you begin. Chances are you may need a professional plumber to make tube links.
This post will help you install a brand-new bathtub in your bathroom if you have already gotten a brand-new tub as well as don't need to transform the setup of your previous water pipes.
Your tools as well as product list must make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is detach the water supply. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of eliminating the existing faucets can be quite problematic as a result of the restricted gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming during this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making certain that the washers remain in area in between the faucet and the sink. Safeguard the tap in place with the producer provided backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former kind must be attached to the tap ends initially, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing both wooden boards under its feet, place the bath tub in the needed position. The wooden boards are helpful in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bathtub until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as likewise inspect the overflow outlet and the typical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bath tub needs to wait up until the bathtub has been used at least when as this will resolve it into its final placement.
Getting ready for the Installation
First of all, the sustaining framework provided with the bathroom should be fitted (if called for) according to the maker's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable tap ports to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to split an inflexible seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, bring about difficulties with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and cartridges, and can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealer can crack relatively very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also quickly offered on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put a remark directly below. We will be interested to know your reactions about this blog post. In hopes that you come back again in the future. Enjoyed reading our content? Please share it. Help someone else discover it. Thanks a lot for your time. Don't forget to come visit our website back soon.
Leading plumbing expertise for emergencies.